Enerpac RC-Series Plunger clevis attachments Bedienungsanleitung PDF herunterladen

POWERFUL SOLUTIONS. GLOBAL FORCE.

1.0 IMPORTANT RECEIVING INSTRUCTIONS

Visually inspect all components for shipping damage. Shipping damage is

not covered by warranty. If shipping damage is found, notify carrier at once.

The carrier is responsible for all repair and replacement costs resulting from

damage in shipment.

SAFETY FIRST

2.0 SAFETY ISSUES

Read all instructions, warnings and cautions carefully.

Follow all safety precautions to avoid personal injury or

property damage during system operation. Enerpac cannot

be responsible for damage or injury resulting from unsafe product use, lack

of maintenance or incorrect product and/or system operation. Contact

Enerpac when in doubt as to the safety precautions and operations. If you

have never been trained on high-pressure hydraulic safety, consult your

distribution or service center for a free Enerpac Hydraulic safety course.

Failure to comply with the following cautions and warnings could cause

equipment damage and personal injury.

A CAUTION is used to indicate correct operating or maintenance

procedures and practices to prevent damage to, or destruction of

equipment or other property.

A WARNING indicates a potential danger that requires correct procedures

or practices to avoid personal injury.

A DANGER is only used when your action or lack of action may cause

serious injury or even death.

WARNING: Wear proper personal protective gear when

operating hydraulic equipment.

WARNING: Stay clear of loads supported by hydraulics. A

cylinder, when used as a load lifting device, should never be

used as a load holding device. After the load has been raised

or lowered, it must always be blocked mechanically.

WARNING: USE ONLY RIGID PIECES TO HOLD LOADS.

Carefully select steel or wood blocks that are capable of

supporting the load. Never use a hydraulic cylinder as a shim

or spacer in any lifting or pressing application

. DANGER: To avoid personal injury keep hands and feet

away from cylinder and workpiece during operation.

WARNING: Do not exceed equipment ratings. Never attempt

to lift a load weighing more than the capacity of the cylinder.

Overloading causes equipment failure and possible personal

injury. The cylinders are designed for a max. pressure of 700

bar [10,000 psi]. Do not connect a jack or cylinder to a pump with a

higher pressure rating.

Never set the relief valve to a higher pressure than the

maximum rated pressure of the pump. Higher settings may

result in equipment damage and/or personal injury.

WARNING: The system operating pressure must not exceed the

pressure rating of the lowest rated component in the system.

Install pressure gauges in the system to monitor operating

pressure. It is your window to what is happening in the system.

CAUTION: Avoid damaging hydraulic hose. Avoid sharp bends

and kinks when routing hydraulic hoses. Using a bent or

kinked hose will cause severe back-pressure. Sharp bends and

kinks will internally damage the hose leading to premature hose failure.

Do not drop heavy objects on hose. A sharp impact may

cause internal damage to hose wire strands. Applying

pressure to a damaged hose may cause it to rupture.

IMPORTANT: Do not lift hydraulic equipment by the hoses

or swivel couplers. Use the carrying handle or other means

of safe transport.

CAUTION: Keep hydraulic equipment away from flames

and heat. Excessive heat will soften packings and seals,

resulting in fluid leaks. Heat also weakens hose materials

and packings. For optimum performance do not expose equipment to

temperatures of 65°C [150°F] or higher. Protect hoses and cylinders

from weld spatter.

DANGER: Do not handle pressurized hoses. Escaping oil

under pressure can penetrate the skin, causing serious injury.

If oil is injected under the skin, see a doctor immediately.

WARNING: Only use hydraulic cylinders in a coupled system.

Never use a cylinder with unconnected couplers. If the

cylinder becomes extremely overloaded, components can

fail catastrophically causing severe personal injury.

WARNING: BE SURE SETUP IS STABLE BEFORE LIFTING

LOAD. Cylinders should be placed on a flat surface that can

support the load. Where applicable, use a cylinder base for

added stability. Do not weld or otherwise modify the cylinder

to attach a base or other support.

Avoid situations where loads are not directly centered on the

cylinder plunger. Off-center loads produce considerable

strain on cylinders and plungers. In addition, the load may

slip or fall, causing potentially dangerous results.

Distribute the load evenly across the entire saddle surface.

Always use a saddle to protect the plunger.

IMPORTANT: Hydraulic equipment must only be serviced by

a qualified hydraulic technician. For repair service, contact

the Authorized ENERPAC Service Center in your area. To

protect your warranty, use only ENERPAC oil.

WARNING: Immediately replace worn or damaged parts by

genuine ENERPAC parts. Standard grade parts will break

causing personal injury and property damage. ENERPAC

parts are designed to fit properly and withstand high loads.

Instruction Sheet

PLUNGER CLEVIS ATTACHMENTS

L1327 Rev. B 06/13

1 2

Inhaltsverzeichnis

Seite 1 - PLUNGER CLEVIS ATTACHMENTS

POWERFUL SOLUTIONS. GLOBAL FORCE.1.0 IMPORTANT RECEIVING INSTRUCTIONSVisually inspect all components for shipping damage. Shipping damage isnot cov

Seite 2 - Attaches to cylinder plunger

3.0 OPERATION1. Base clevis attachments arefor use on ENERPAC RCsingle-acting cylinders.Cylinder capacities are 5through 30 ton (see Table1).2. The c

Kommentare zu diesen Handbüchern

Keine Kommentare

Enerpac RC-Series Plunger clevis attachments Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hissen Enerpac RC-Series Plunger clevis attachments herunter. Enerpac RC-Series Plunger clevis attachments User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hissen Enerpac RC-Series Plunger clevis attachments