Enerpac W35000 Bedienungsanleitung

Instruction SheetW22000 SeriesW35000 SeriesHydraulic Torque WrenchL3009English (GB) Rev. C 12/2011

105 Maintenance and troubleshootingPreventative maintenance can be carried out by the user. Full maintenance must be carried out by an approved and a

115.2 Full maintenance5.2.1 The hydraulic drive unit• Remove the circlip from the swivel coupling.• Remove the couplings.• Remove the swivel-coupli

12• As a check, refer to figure M and the tables below for the correct height of the drive unit retaining pin (Y). Pin Height - W22000 Series(fig. M

136 Technical specifications - W22000 Series6.1 W22000 Series - Capacities and dimensions (fig. N) Cassette capacity * mm 75 - 135 inch 2 15/

146.2 Cassette capacities - W22000 Series6.2.1 Metric system table (See fig. N for dimensions S, G and H)Cassette (S) (G) (H) WeightModel mm mm

156.2.2 Imperial system table (See fig. N for dimensions S, G and H)Cassette (S) (G) (H) WeightModel inch inch inch lbs W22215 2 15/16 4.02 2.64

16Pump pressure (bar) Torque (Nm) 69 3.051 83 3.670 97 3.670110 4.864124 5.483138 6.102152 6.721166 7.340179 7.915193 8.534207 9.153221 9.772234

17Pump pressure (psi) Torque (Ft.lbs)1,000 2,2501,200 2,7001,400 3,1501,600 3,6001,800 4,0502,000 4,5002,200 4,9502,400 5,4002,600 5,8502,800 6,300

18NOTES:

197 Technical specifications - W35000 Series7.1 W35000 Series - Capacities and dimensions (fig. O) Cassette capacity * mm 80 - 155 inch 3 1/8

2

207.2 Cassette capacities - W35000 Series7.2.1 Metric system table (See fig. O for dimensions S, E, G and H)Cassette (S) (E) (G) (H) WeightMode

217.2.2 Imperial system table (See fig. O for dimensions S, E, G and H)Cassette (S) (E) (G) (H) WeightModel inch inch inch inch lbs W35302 3

22Pump pressure (bar) Torque (Nm) 69 4.745 83 5.708 97 6.671110 7.565124 8.528138 9.491152 10.453166 11.416179 12.310193 13.273207 14.236221 15.

23Pump pressure (psi) Torque (Ft.lbs)1,000 3,500 1,200 4,200 1,400 4,900 1,600 5,600 1,800 6,300 2,000 7,000 2,200 7,700 2,400 8,400 2,600 9,100 2,

248 Replacement parts and recommended tools8.1 To order replacement parts For replacement parts information, refer to the Enerpac repair parts shee

25NOTES:

26NOTES:

27NOTES:

© Enerpac 11-2011 - Subject to change without notice.Australia and New ZealandActuant Australia Ltd. Block V Unit 3Regents Park Estate391 Park RoadReg

3 Index1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Safety . . . . . . . . . . .

4CE Declaration of conformityEnerpac declares that the W22000 and W35000 Series torque wrenches meet the applicable standards and directives issued by

5of the tool when it is in operation. If the tool separates from the nut or bolt during operation it will detach in that direction.- Tightening and l

6Fig. AFig. B3 Assembly and adjustments3.1 Overview and features(fig. A or B)1 Hexagon ratchet2 Cassette3A Swivel coupling or 3B TSP-Pro swivel cou

7 Fig. F• Push the release lever (7) back into the cassette (2). Make sure the ball detent clicks into place.Do not operate the tool if the cassette

84 Operation4.1 Prior to operation- Make sure the nut or bolt to be fastened is clean and free of dust.- Make sure the nut or bolt runs correctly o

9Fig. J4.3.2 To loosen a nut or bolt (fig. I & J)• Apply penetrating oil to the threads. Allow the oil to soak.• Position the tool on the nut or